机载通信电台通电老炼检测系统设计与实现

为保证航材备件的完好率，解决仓储机载通信电台长期不通电导致的装备性能下降甚至出现故障的问题，综合运用自动测试、虚拟仪器、面向信号设计等技术，以计算机为核心，以PXI仪器、GPIB仪器为依托，以多种总线接口为纽带，构建了一种可靠性高、通用性好、操作简便、可扩展性强的自动化通电老炼平台。通过在航材仓库中使用，证明该电台老炼检测系统降低了仓储通信电台的失效率，提高了仓储电台的完好率。     

Compilation of Modern Technologies To Map Genome-Wide Cytosine Modifications in DNA

Over the past few decades, various DNA modification detection methods have been developed; many of the high-resolution methods are based on bisulfite treatment, which leads to DNA degradation, to a degree. Thus, novel bisulfite-free approaches have been developed in recent years and shown to be useful for epigenome analysis in otherwise difficult-to-handle, but important, DNA samples, such as hmC-seal and hmC-CATCH. Herein, an overview of advances in the development of epigenome sequencing methods for these important DNA modifications is provided.     

Effect of ZnO/K2O ratio on the crystallization sequence and microstructure of lithium disilicate glass-ceramics

The effect of ZnO/K₂O (Z/K) ratio on the crystallization sequence and microstructure of lithium disilicate (Li₂Si₂O₅: LS2) glass-ceramics was carefully investigated for the SiO₂-Li₂O-K₂O-ZnO-P₂O₅ system. The Z/K ratios of precursor glasses were varied from 0 to 3.5 while the nucleating agent of P₂O₅ and glass modifiers of ZnO plus K₂O were fixed to have 1.5 and 4.5 mol% relative to LS2, respectively. For the samples prepared by two-stage heat treatments of 500 °C for 1 h and 800 °C for 2 h in air, the LS2 nucleation rate was increased with increasing the Z/K ratio due to the variation in crystallization sequence from type II (Li₂SiO₃: LS) to type I (LS + LS2) in addition to an amorphous phase separation in base glass. Consequently, with increasing the Z/K ratio, the LS2 crystalline phase within the glass matrix continuously changed from larger acicular ones to smaller equiaxed ones.     

高强WSTi544221合金组织与性能研究

研究了轧制变形量对WSTi544221合金棒材显微组织和力学性能的影响,并对Φ10 mm规格的棒材进行不同制度的固溶+时效处理,对比了不同热处理状态下棒材的组织和力学性能。结果表明,随着轧制变形量的增大,WSTi544221合金棒材的晶粒细化程度增大,强度逐渐提高,但塑性变化不大。经870℃×1 h/WC+520℃×6 h/AC固溶+时效处理后,强度与塑性可以获得良好匹配,当抗拉强度达到1 610 MPa、屈服强度达到1 531 MPa时,延伸率和断面收缩率可分别保持在12%和43%。     

基于深度学习的文本自动摘要方案

针对自然语言处理（NLP）生成式自动摘要领域的语义理解不充分、摘要语句不通顺和摘要准确度不够高的问题，提出了一种新的生成式自动摘要解决方案，包括一种改进的词向量生成技术和一个生成式自动摘要模型。改进的词向量生成技术以Skip-Gram方法生成的词向量为基础，结合摘要的特点，引入词性、词频和逆文本频率三个词特征，有效地提高了词语的理解；而提出的Bi-MulRnn+生成式自动摘要模型以序列映射（seq2seq）与自编码器结构为基础，引入注意力机制、门控循环单元（GRU）结构、双向循环神经网络（BiRnn）、多层循环神经网络（MultiRnn）和集束搜索，提高了生成式摘要准确性与语句流畅度。基于大规模中文短文本摘要（LCSTS）数据集的实验结果表明，该方案能够有效地解决短文本生成式摘要问题，并在Rouge标准评价体系中表现良好，提高了摘要准确性与语句流畅度。     

考虑决策者时序偏好的时域证据融合方法

针对时域不确定信息的融合难题，为充分体现时域信息融合的动态性特点和时间因素对融合的影响，在证据理论的基础上，提出一种考虑决策者时序偏好的时域证据融合方法。首先将决策者对时序的偏好融入时域证据融合，通过分析时域证据序列的特点，在定义时序记忆因子的基础上，对决策者的时序偏好进行度量；然后通过构建优化模型求解时序权重，再结合证据信任度的概念，对证据源进行修正；最后利用Dempster组合规则对修正后的证据进行融合。数值算例表明，与没有考虑时间因素的融合方法相比，考虑决策者时序偏好的证据融合方法可以有效处理时域信息序列中的冲突信息，得到合理的融合结果；同时，所提方法充分考虑了时域证据序列的信任度和决策者的主观偏好，可以反映决策者主观因素对时域证据融合的影响，较好地体现了时域证据融合的动态性特点。     

Effect of hydrothermal aging on dental multilayered zirconia for monolithic restorations: An in vitro study

The aim of this in vitro study was to investigate the changes in mechanical, optical, and surface properties of multilayered zirconia during hydrothermal aging.One conventional block (Katana Zirconia HT) and three multilayered blocks (Katana Zirconia ML, STML, and UTML) of monolithic zirconia were examined. Bar-shaped specimens were autoclaved at 134°C and 0.2MPa for 0, 5, and 10 h. The Young's modulus, three-point flexural strength, and nanoindentation hardness were measured to evaluate the mechanical properties. The surface roughness, phase distribution, surface microstructure, and elemental composition were measured to analyze the surface properties. The contrast ratio and total transmittance were measured via spectrophotometry to evaluate the optical properties. Statistical differences were analyzed using appropriate ANOVA, Tukey HSD post hoc tests, and independent and paired sample t-tests (α = .05).The monoclinic phase increased gradually after hydrothermal aging. The yttrium and zirconium concentrations decreased, and the oxygen concentration and the surface roughness increased in all specimens (P<.05) after the aging process. All specimens showed significant grain push-out and microcracks. The total transmittance increased, and the contrast ratio and Young's modulus decreased in all specimens (P<.05) after the aging process. The nanoindentation hardness and three-point flexural strength exhibited a decreasing tendency after the aging process. However, there were no statistical differences (P>.05) between the materials. Significant interactions between material grades and hydrothermal aging were found for all the properties studied (P<.001).Microstructural alterations and significant phase transformations were detected on the surface of the multilayered zirconia after hydrothermal aging. The hydrothermal aging led to increased surface roughness, opaqueness, and elasticity of multilayered zirconia. The optical, mechanical, and surface properties of multilayered zirconia were influenced by the grade of the material after hydrothermal aging. Careful consideration of the grade of materials is necessary for the appropriate selection of multilayered zirconia ceramics for monolithic restorations.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

The cumulative power of incremental innovation and the role of project sequence management

In innovation and project management studies incremental development projects are perceived as theoreticlly and organisationally uninteresting. By means of a longitudinal study of product improvement projects at an automobile firm, this paper challenges such views and shows how the cumulative impact of the studied sequence resulted in a competitive repositioning of the company's product portfolio during a financially difficult period. Project managers achieved this by transcending the separation between exploration and exploitation projects; they not only adhered to time, cost and quality goals but also tried out new ways of testing and experimenting with controversial technical ideas. The paper analyzes the intensive inter project learning that generated these ambidextrous capabilities and emphasizes that practices at the project-level need to be buttressed by expanded management learning and capability development also at the sequence level.